LV4B-13B414-BA Rear Bumper Light for FORD Escape 2020 Right

LV4B-13B414-BA Rear Bumper Light Overview

This product is listed for FORD Escape 2020 at the right rear-bumper position. Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

For a repeat order of the right version, record the approved side and vehicle application for repeat-order identification so a passive reflector is not confused with an illuminated assembly.

Application and Rear-Bumper Position

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Production date and regional bumper specification should be reviewed when several near-identical versions are available.

On the 2020 Escape bumper layout, confirm that the cable exit, where fitted, clears the bumper reinforcement to verify that the photographed configuration matches the vehicle in the workshop.

At the workshop selection stage for Escape, confirm that any connector seal remains square when the housing is fully seated to avoid contact with wiring, body edges or hot exhaust components.

Optical Face and Connector Review

Do not add wiring to a reflector-only application; use the photographs to distinguish illuminated and passive versions.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

At the right rear-bumper position, use the opposite-side component only as an alignment reference, not as an interchange part to keep the optical face level with the surrounding painted surface.

When reviewing the 2020 vehicle, compare the outer lens edge with the moulded bumper recess before any modification is made to the bumper or replacement part.

Workshop Fitting Sequence

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

For the FORD Escape application, inspect the lower valance and nearby exhaust trim for adequate operating clearance before deciding whether original hardware is suitable for reuse.

For this Escape body configuration, check the rear housing projection against the space behind the bumper skin because facelift bumpers can retain the same vehicle name with different apertures.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: LV4B-13B414-BA

Cross-reference numbers: LV4B-13B414-BA

Internal item code: FD04004-002

Vehicle brand: FORD

Vehicle model: Escape

Model year: 2020

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

The visible face should remain separated from tape, staples and loose hardware throughout transport.

Before approving the Escape part for packing, compare the bumper corner radius with the product face from more than one viewing angle so left- and right-hand stock cannot be mixed during consolidation.

Before fitting the right unit, align each locating tab with the matching slot before applying hand pressure so the approved product can be picked consistently in a mixed wholesale order.

Frequently Asked Questions

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

Where the application is uncertain, send bumper-opening and rear-housing photographs for comparison first.

Physical comparison: Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Lighting function: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

Post-fit check: Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

Wholesale enquiry: For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.

Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.