FB5Z-1 5A449-D FB53-17A849-AE Rear Bumper Light for FORD Explorer 2018 Right

FB5Z-1 5A449-D FB53-17A849-AE Rear Bumper Light Overview

This product is listed for FORD Explorer 2018 at the right rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

At the workshop selection stage for Explorer, confirm that the cable exit, where fitted, clears the bumper reinforcement before any modification is made to the bumper or replacement part.

Rear-Bumper Geometry Review

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

At the right rear-bumper position, confirm that any connector seal remains square when the housing is fully seated before deciding whether original hardware is suitable for reuse.

When reviewing the 2018 vehicle, use the opposite-side component only as an alignment reference, not as an interchange part because facelift bumpers can retain the same vehicle name with different apertures.

Lens, Housing and Harness Comparison

Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.

Protect the exposed face from tools and fasteners while the bumper liner is open for access.

For the FORD Explorer application, compare the outer lens edge with the moulded bumper recess so left- and right-hand stock cannot be mixed during consolidation.

For this Explorer body configuration, inspect the lower valance and nearby exhaust trim for adequate operating clearance so the approved product can be picked consistently in a mixed wholesale order.

Installation Completion

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.

Before approving the Explorer part for packing, check the rear housing projection against the space behind the bumper skin so hidden brackets are not loaded or bent during installation.

Before fitting the right unit, compare the bumper corner radius with the product face from more than one viewing angle to preserve access for a final electrical test where a lamp circuit is present.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: FB5Z-1 5A449-D FB53-17A849-AE

Cross-reference numbers: FB5Z-1 5A449-D FB53-17A849-AE

Internal item code: FD04004-052

Vehicle brand: FORD

Vehicle model: Explorer

Model year: 2018

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

The visible face should remain separated from tape, staples and loose hardware throughout transport.

While the FORD bumper opening is accessible, align each locating tab with the matching slot before applying hand pressure to reduce clip damage during a no-force trial installation.

During comparison of the FORD rear component, check whether the original component uses a separate retainer or an integral locking tab to prevent a visually similar version from sitting proud of the bumper.

Frequently Asked Questions

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Request a Product-Specific Quote

Repeat buyers can reference the vehicle application and side from their previous approved sample.

Physical comparison: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.

Lighting function: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

Post-fit check: After installation, confirm the lens is level with nearby trim and that no retaining tab has backed out.

Wholesale enquiry: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.