92406-H9100 Rear Bumper Light for KIA Rio 2017 Right

92406-H9100 Rear Bumper Light Overview

This product is listed for KIA Rio 2017 at the right rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

During comparison of the KIA rear component, compare the outer lens edge with the moulded bumper recess to prevent a visually similar version from sitting proud of the bumper.

Model, Year and Side Confirmation

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

For a repeat order of the right version, inspect the lower valance and nearby exhaust trim for adequate operating clearance before the packaging and carton marking are finalized.

On the 2017 Rio bumper layout, check the rear housing projection against the space behind the bumper skin before inner liners make the rear attachment points difficult to inspect.

Reflector Housing and Wiring Details

Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.

Protect the exposed face from tools and fasteners while the bumper liner is open for access.

At the workshop selection stage for Rio, compare the bumper corner radius with the product face from more than one viewing angle so the visible gap remains even after every retaining point is engaged.

At the right rear-bumper position, align each locating tab with the matching slot before applying hand pressure so the lens and housing are supported without distortion.

Installation Preparation

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.

When reviewing the 2017 vehicle, check whether the original component uses a separate retainer or an integral locking tab so a passive reflector is not confused with an illuminated assembly.

For the KIA Rio application, verify the fastener direction and the shape of the concealed support frame to verify that the photographed configuration matches the vehicle in the workshop.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92406-H9100

Cross-reference numbers: 92406-H9100

Internal item code: KA04004-038

Vehicle brand: KIA

Vehicle model: Rio

Model year: 2017

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.

For this Rio body configuration, protect the visible surface until the full perimeter gap has been accepted to avoid contact with wiring, body edges or hot exhaust components.

Before approving the Rio part for packing, review the reflector texture and lens colour in neutral workshop light to keep the optical face level with the surrounding painted surface.

Frequently Asked Questions

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Request a Product-Specific Quote

A product-specific quotation can be prepared after the vehicle, side and destination are confirmed.

Bumper interface: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.

Product function: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

Trade-order details: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.