92406-2B500 Rear Bumper Light for HYUNDAI Santa Fe 2009 Right

92406-2B500 Rear Bumper Light Overview

This product is listed for HYUNDAI Santa Fe 2009 at the right rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

For a repeat order of the right version, check whether the original component uses a separate retainer or an integral locking tab to reduce clip damage during a no-force trial installation.

Model, Year and Side Confirmation

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

On the 2009 Santa Fe bumper layout, verify the fastener direction and the shape of the concealed support frame to prevent a visually similar version from sitting proud of the bumper.

At the workshop selection stage for Santa Fe, protect the visible surface until the full perimeter gap has been accepted before the packaging and carton marking are finalized.

Reflector Housing and Wiring Details

If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

At the right rear-bumper position, review the reflector texture and lens colour in neutral workshop light before inner liners make the rear attachment points difficult to inspect.

When reviewing the 2009 vehicle, record the approved side and vehicle application for repeat-order identification so the visible gap remains even after every retaining point is engaged.

Installation Preparation

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Check the opposite side as a reference for height, angle and edge gap before completing the repair.

For the HYUNDAI Santa Fe application, confirm that the cable exit, where fitted, clears the bumper reinforcement so the lens and housing are supported without distortion.

For this Santa Fe body configuration, confirm that any connector seal remains square when the housing is fully seated so a passive reflector is not confused with an illuminated assembly.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92406-2B500

Cross-reference numbers: 92406-2B500

Internal item code: HY04004-026

Vehicle brand: HYUNDAI

Vehicle model: Santa Fe

Model year: 2009

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Before sealing the carton, compare the packed side and quantity with the buyer’s order line.

Before approving the Santa Fe part for packing, use the opposite-side component only as an alignment reference, not as an interchange part to verify that the photographed configuration matches the vehicle in the workshop.

Before fitting the right unit, compare the outer lens edge with the moulded bumper recess to avoid contact with wiring, body edges or hot exhaust components.

Frequently Asked Questions

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Request a Product-Specific Quote

Where the application is uncertain, send bumper-opening and rear-housing photographs for comparison first.

Housing match: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.

Reflector or lamp role: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Purchase information: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.