92406-1Y500 Rear Bumper Light for KIA Picanto 2014 Right

92406-1Y500 Rear Bumper Light Overview

This product is listed for KIA Picanto 2014 at the right rear-bumper position. Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

Before fitting the right unit, use the opposite-side component only as an alignment reference, not as an interchange part so the approved product can be picked consistently in a mixed wholesale order.

Vehicle-Specific Selection

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

While the KIA bumper opening is accessible, compare the outer lens edge with the moulded bumper recess so hidden brackets are not loaded or bent during installation.

During comparison of the KIA rear component, inspect the lower valance and nearby exhaust trim for adequate operating clearance to preserve access for a final electrical test where a lamp circuit is present.

Passive Reflector or Lamp Configuration

Do not add wiring to a reflector-only application; use the photographs to distinguish illuminated and passive versions.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

For a repeat order of the right version, check the rear housing projection against the space behind the bumper skin to reduce clip damage during a no-force trial installation.

On the 2014 Picanto bumper layout, compare the bumper corner radius with the product face from more than one viewing angle to prevent a visually similar version from sitting proud of the bumper.

Fitting Guidance and Testing

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Check the opposite side as a reference for height, angle and edge gap before completing the repair.

At the workshop selection stage for Picanto, align each locating tab with the matching slot before applying hand pressure before the packaging and carton marking are finalized.

At the right rear-bumper position, check whether the original component uses a separate retainer or an integral locking tab before inner liners make the rear attachment points difficult to inspect.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92406-1Y500

Cross-reference numbers: 92406-1Y500

Internal item code: KA04004-020

Vehicle brand: KIA

Vehicle model: Picanto

Model year: 2014

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.

When reviewing the 2014 vehicle, verify the fastener direction and the shape of the concealed support frame so the visible gap remains even after every retaining point is engaged.

For the KIA Picanto application, protect the visible surface until the full perimeter gap has been accepted so the lens and housing are supported without distortion.

Frequently Asked Questions

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Bumper interface: Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Product function: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Use the removed component as the physical reference for outer shape, housing projection and clip location.

Post-fit check: Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Trade-order details: For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.

Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.