92405-H9100 Rear Bumper Light for KIA Rio 2017 Left

92405-H9100 Rear Bumper Light Overview

This product is listed for KIA Rio 2017 at the left rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.

At the left rear-bumper position, check whether the original component uses a separate retainer or an integral locking tab to verify that the photographed configuration matches the vehicle in the workshop.

Bumper Opening and Vehicle Match

Review the corner radius, edge return and rear fastening points against the original bumper opening.

The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.

When reviewing the 2017 vehicle, verify the fastener direction and the shape of the concealed support frame to avoid contact with wiring, body edges or hot exhaust components.

For the KIA Rio application, protect the visible surface until the full perimeter gap has been accepted to keep the optical face level with the surrounding painted surface.

Lens Construction and Powered Variants

Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

For this Rio body configuration, review the reflector texture and lens colour in neutral workshop light before any modification is made to the bumper or replacement part.

Before approving the Rio part for packing, record the approved side and vehicle application for repeat-order identification before deciding whether original hardware is suitable for reuse.

Mounting and Final Verification

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

Before fitting the left unit, confirm that the cable exit, where fitted, clears the bumper reinforcement because facelift bumpers can retain the same vehicle name with different apertures.

While the KIA bumper opening is accessible, confirm that any connector seal remains square when the housing is fully seated so left- and right-hand stock cannot be mixed during consolidation.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92405-H9100

Cross-reference numbers: 92405-H9100

Internal item code: KA04004-037

Vehicle brand: KIA

Vehicle model: Rio

Model year: 2017

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.

The visible face should remain separated from tape, staples and loose hardware throughout transport.

During comparison of the KIA rear component, use the opposite-side component only as an alignment reference, not as an interchange part so the approved product can be picked consistently in a mixed wholesale order.

For a repeat order of the left version, compare the outer lens edge with the moulded bumper recess so hidden brackets are not loaded or bent during installation.

Frequently Asked Questions

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

The quotation can include export packing requirements once the required variant and order volume are known.

Physical comparison: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.

Wholesale enquiry: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.