92405-D4500 Rear Bumper Light for KIA K5 2019 Left

92405-D4500 Rear Bumper Light Overview

This product is listed for KIA K5 2019 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.

Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

At the workshop selection stage for K5, compare the bumper corner radius with the product face from more than one viewing angle so a passive reflector is not confused with an illuminated assembly.

Vehicle-Specific Selection

Review the corner radius, edge return and rear fastening points against the original bumper opening.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

At the left rear-bumper position, align each locating tab with the matching slot before applying hand pressure to verify that the photographed configuration matches the vehicle in the workshop.

When reviewing the 2019 vehicle, check whether the original component uses a separate retainer or an integral locking tab to avoid contact with wiring, body edges or hot exhaust components.

Passive Reflector or Lamp Configuration

For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

For the KIA K5 application, verify the fastener direction and the shape of the concealed support frame to keep the optical face level with the surrounding painted surface.

For this K5 body configuration, protect the visible surface until the full perimeter gap has been accepted before any modification is made to the bumper or replacement part.

Fitting Guidance and Testing

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Before approving the K5 part for packing, review the reflector texture and lens colour in neutral workshop light before deciding whether original hardware is suitable for reuse.

Before fitting the left unit, record the approved side and vehicle application for repeat-order identification because facelift bumpers can retain the same vehicle name with different apertures.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92405-D4500

Cross-reference numbers: 92405-D4500

Internal item code: KA04004-053

Vehicle brand: KIA

Vehicle model: K5

Model year: 2019

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Projecting tabs should be supported with shaped material instead of carrying the weight of other products.

While the KIA bumper opening is accessible, confirm that the cable exit, where fitted, clears the bumper reinforcement so left- and right-hand stock cannot be mixed during consolidation.

During comparison of the KIA rear component, confirm that any connector seal remains square when the housing is fully seated so the approved product can be picked consistently in a mixed wholesale order.

Frequently Asked Questions

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Request a Product-Specific Quote

Repeat buyers can reference the vehicle application and side from their previous approved sample.

Shape and clips: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.

Rear visibility role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Use the removed component as the physical reference for outer shape, housing projection and clip location.

Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.

Quotation details: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.