92405-A7000 Rear Bumper Light for KIA K3 2013 Left

92405-A7000 Rear Bumper Light Overview

This product is listed for KIA K3 2013 at the left rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

For the KIA K3 application, verify the fastener direction and the shape of the concealed support frame before deciding whether original hardware is suitable for reuse.

Vehicle Fitment and Bumper Interface

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

For this K3 body configuration, protect the visible surface until the full perimeter gap has been accepted because facelift bumpers can retain the same vehicle name with different apertures.

Before approving the K3 part for packing, review the reflector texture and lens colour in neutral workshop light so left- and right-hand stock cannot be mixed during consolidation.

Reflector, Lens and Electrical Configuration

If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.

Protect the exposed face from tools and fasteners while the bumper liner is open for access.

Before fitting the left unit, record the approved side and vehicle application for repeat-order identification so the approved product can be picked consistently in a mixed wholesale order.

While the KIA bumper opening is accessible, confirm that the cable exit, where fitted, clears the bumper reinforcement so hidden brackets are not loaded or bent during installation.

Installation and Functional Check

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Check the opposite side as a reference for height, angle and edge gap before completing the repair.

During comparison of the KIA rear component, confirm that any connector seal remains square when the housing is fully seated to preserve access for a final electrical test where a lamp circuit is present.

For a repeat order of the left version, use the opposite-side component only as an alignment reference, not as an interchange part to reduce clip damage during a no-force trial installation.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 92405-A7000

Cross-reference numbers: 92405-A7000

Internal item code: KA04004-057

Vehicle brand: KIA

Vehicle model: K3

Model year: 2013

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

The visible face should remain separated from tape, staples and loose hardware throughout transport.

On the 2013 K3 bumper layout, compare the outer lens edge with the moulded bumper recess to prevent a visually similar version from sitting proud of the bumper.

At the workshop selection stage for K3, inspect the lower valance and nearby exhaust trim for adequate operating clearance before the packaging and carton marking are finalized.

Frequently Asked Questions

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Request a Product-Specific Quote

AutoParts can review the pictured configuration before preparing a quantity-based offer.

Physical comparison: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.

Lighting function: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Production date and regional bumper specification should be reviewed when several near-identical versions are available.

Post-fit check: Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Wholesale enquiry: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.