92101-B4020 Head Light for HYUNDAI i10 2014 Left

Head Light Assembly Overview

The listed unit is designed for the stated vehicle position and should be matched to the removed headlamp before installation. It is catalogued under OE reference 92101-B4020 for HYUNDAI i10 2014, with the left position identified in the source record.

The observable lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.

Lighting Function and Optical Configuration

Verify the number and position of optical chambers and verify whether daytime lighting is integrated into the main housing.

For the i10 application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use non-matching internal modules, beam controls and daytime-light signatures.

Vehicle Fitment and Body Interface

Cross-check the rear housing depth, outer lens contour and the relationship between the grille-side and fender-side edges with the removed lamp.

Verify that repaired body supports are square before judging lamp fit, because collision distortion can imitate a part mismatch.

Connector and Control Hardware

The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.

Verify the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.

Installation and Beam Alignment

After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.

A qualified workshop should inspect surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.

Automotive Lighting Product Specifications

Product type: Head Light Assembly

Primary OE reference: 92101-B4020

Cross-reference numbers: 92101-B4020

Internal item code: HY04001-303

Vehicle brand: HYUNDAI

Vehicle model: i10

Model year: 2014

Installation position: Left front

Lighting configuration: Match the photographed optical configuration

Wholesale Supply and Protective Packing

Packing should distribute load around the housing rather than the lens and preserve dry, clean connector and module interfaces.

When requesting a quotation, supply the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.

Application-Specific Comparison Notes

For this left HYUNDAI i10 headlamp, the match the photographed optical configuration specification should be assessed together with the 2014 body application. Evaluate the rear housing depth, outer lens contour and the relationship between the grille-side and fender-side edges with the removed lamp.

The left i10 lighting package should remain the reference during electrical review. Do not use connector colour as the only selection point; terminal geometry, locking tabs and installed modules must also agree.

When fitting the HYUNDAI i10 unit at the left front position, preserve even body gaps and the intended beam orientation. After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.

Frequently Asked Questions

How should the lamp be protected during shipping?

The lens needs isolation from carton pressure, while the rear housing and projecting tabs require stable internal support.

How can connector compatibility be reviewed?

Cross-check keying, terminal count, latch direction and wire exit, then establish any required ballast, driver or levelling motor.

Can a headlamp be chosen by appearance alone?

No. The left lamp must also match the optical system, electrical interface, mounting features and market specification.

Are bulbs and electronic modules included?

The included components are those observable in the product photographs. Inspect bulbs, caps, motors, ballasts and LED modules separately.

Why must the rear housing be compared?

A similar lens can conceal a non-matching casing depth, cap arrangement or bracket offset, preventing correct seating in the body opening.

Housing comparison: Lay the replacement beside the removed unit and evaluate overall depth, edge returns, vent locations and rear-cover clearance.

Optical system: Verify the number and position of optical chambers and validate whether daytime lighting is integrated into the main housing.

Electrical interface: Match the connector key, pin arrangement, latch direction and cable exit; LED or xenon versions may also require compatible control hardware.

Mounting points: Validate that repaired body supports are square before judging lamp fit, because collision distortion can imitate a part mismatch.

Installation guidance: Keep wiring clear of hot or moving components, then test low beam, high beam, indicator and daytime lighting where applicable.

Wholesale packing: For wholesale supply, the lens should be isolated from carton pressure while the rear shell, adjusters and projecting mounting tabs are supported.

Application-specific focus: For the left HYUNDAI i10 application with match the photographed optical configuration, inspect reflector colour, projector presence and any decorative internal trim before approving a left/right pair for one vehicle.