92101-4X510 Head Light for KIA K2 2014 Left

Head Light Assembly Overview

The headlamp shown should be chosen as a complete vehicle-specific assembly, with side and lighting version confirmed before ordering. It is catalogued under OE reference 92101-4X510 for KIA K2 2014, with the left position identified in the source record.

The external lens, internal optical layout, rear casing and attachment points should be reviewed as one system. A close-looking lamp from another trim or market can differ behind the body opening.

Lighting Function and Optical Configuration

Review the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.

For the K2 application, verify the lighting package fitted to the vehicle. Standard, projector, xenon and LED versions can use alternative internal modules, beam controls and daytime-light signatures.

Vehicle Fitment and Body Interface

Establish that the headlamp sits naturally in the body opening and follows the bonnet, grille and fender lines without forced alignment.

A correct assembly should align at the locating points without drilling, trimming or forcing the vehicle-side brackets.

Connector and Control Hardware

The electrical interface should seat without modification, and the harness must reach the connection without tension or contact with sharp edges.

Establish the supply scope shown in the product photographs. Bulbs, rear caps, levelling motors, ballasts, LED drivers and auxiliary brackets may vary between versions and should be checked separately.

Installation and Beam Alignment

Keep wiring clear of hot or moving components, then test low beam, high beam, indicator and daytime lighting where applicable.

A qualified workshop should look over surrounding supports for damage, complete the electrical tests and set the headlamp beam according to local requirements after installation.

Automotive Lighting Product Specifications

Product type: Head Light Assembly

Primary OE reference: 92101-4X510

Cross-reference numbers: 92101-4X510

Internal item code: KA04001-163

Vehicle brand: KIA

Vehicle model: K2

Model year: 2014

Installation position: Left front

Lighting configuration: premium equipment version

Wholesale Supply and Protective Packing

Packing should distribute load around the housing rather than the lens and preserve dry, clean connector and module interfaces.

When requesting a quotation, supply the vehicle application, production period, required side, lighting technology, quantity and destination. Original-lamp photographs are useful when several versions exist.

Application-Specific Comparison Notes

For this left KIA K2 headlamp, the premium equipment version specification should be assessed together with the 2014 body application. Review the complete lamp body from several angles because a similar lens can conceal a alternative rear casing or bracket offset.

The left K2 lighting package should remain the reference during electrical review. Review terminal count, plug orientation and the location of removable caps before transferring bulbs or reusable electronics.

When fitting the KIA K2 unit at the left front position, preserve even body gaps and the intended beam orientation. After the housing is secured, reconnect the lighting circuit, test every function and carry out professional beam aiming before road use.

Frequently Asked Questions

What information supports a wholesale quotation?

State the KIA K2 application, production year, left side, lighting version, quantity and delivery country.

Are bulbs and electronic modules included?

The included components are those external in the product photographs. Review bulbs, caps, motors, ballasts and LED modules separately.

How should the lamp be protected during shipping?

The lens needs isolation from carton pressure, while the rear housing and projecting tabs require stable internal support.

Are left and right headlamps interchangeable?

No. This application requires the left side; bracket geometry, optical pattern and wiring position are side-specific.

What distinguishes surrounding lighting variants?

Reflector, projector, xenon and LED versions can differ in modules, daytime-light layout, internal bezel and plug configuration.

Housing comparison: Validate that the headlamp sits naturally in the body opening and follows the bonnet, grille and fender lines without forced alignment.

Optical system: Cross-check the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.

Wholesale packing: Carton protection should prevent abrasion on the lens and impact loading on brackets, caps, adjusters or exposed control modules.

Application-specific focus: For the left KIA K2 application with premium equipment version, cross-check the low-beam and high-beam chambers, daytime-running-light strip and indicator section with the vehicle’s original configuration.