8V5955275B Front Left Headlight Washer Nozzle Cover for AUDI A3 2017

8V5955275B Front Left Headlight Washer Nozzle Cover Product Overview

The component shown under 8V5955275B is a front left headlight washer nozzle cover intended for AUDI A3 2017. The visible cover closes the bumper opening around the washer unit and follows the surrounding bumper contour when the nozzle is retracted. Confirm the left orientation, washer-system connection, bumper-side geometry and hatchback / sedan application against the original vehicle part.

Fitment and Washer-System Application for A3

Compatibility for 8V5955275B should be confirmed against AUDI A3 2017 and the left installation side. The review should verify the required left or right installation side, verify that the OE reference is not for the opposite side, and compare product photographs with the removed part from several angles. Use the removed part and product photographs to compare the washer opening beside the correct headlamp, check regional variations in headlamp-cleaning equipment, and use the full OE number, not a partial family reference; finally, compare the hose connection or cover hinge with the original part and match the connector and fluid inlet position where applicable.

Headlight Washer Nozzle Cover Function and Design Notes

The visible and hidden interfaces of AD02010-007 should be checked separately. For this headlight washer nozzle cover, compare the retracted position with the bumper surface, review the sealing area around the hose connection, and check the complete supplied scope against the photographs. A direct comparison with the removed part should additionally inspect the rear reinforcement ribs, compare the visible bumper-side contour, and review the left-to-right mirrored geometry. Before the item is accepted, check the cap hinge or retaining point and inspect the washer outlet for blockage.

OE Identification and Side Confirmation

8V5955275B is the primary OE identity for this left front left headlight washer nozzle cover, while AD02010-007 is the internal item code. Match both references to the vehicle record, then compare the actuator orientation behind the bumper cover. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-007 begins before the bumper area is disturbed: verify that the cover closes without rubbing the bumper and verify that the cap remains attached through a full washer cycle. During trial fitting, transfer reusable clips only after checking their condition, test for drips after the washer pump stops, and tighten bracket hardware only after alignment. Before returning the vehicle to service, trial-fit the component before final fastening, check the headlamp lens receives an even spray, and follow the vehicle workshop procedure for bumper removal.

Receiving Inspection

When AD02010-007 arrives, receiving staff should check painted or primed surfaces under neutral lighting, separate mirrored components immediately after carton opening, and review the production finish against the approved sample. Before workshop release, compare the supplied side with the vehicle repair order, compare left and right orientation before removing protective wrapping, verify the supplied scope before discarding dividers or inner bags, and check the cap hinge or retaining point for free movement. Complete the inspection by ensuring that staff measure the main mounting span when two bumper versions appear similar, protect the visible face again after inspection is complete, and verify the cover contour against the approved product photograph.

Product Technical Specifications

Product type: Front Left Headlight Washer Nozzle Cover

Primary OE reference: 8V5955275B

Cross-reference numbers: 8V5 955 275B 8V5955275B

Internal item code: AD02010-007

Vehicle brand: AUDI

Vehicle model: A3

Model year: 2017

Installation position: Front bumper / headlamp washer area

Side / orientation: Left

Version / specification: hatchback / sedan application

Applicable vehicle: AUDI A3 2017

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8V5955275B, please provide the complete destination address or port, identify the required installation side, and separate left and right items on the packing list. Packing instructions should confirm sample requirements before a bulk order, state the target vehicle application, and request barcode or private-label details when needed. Before dispatch, confirm the preferred incoterm and confirm pallet requirements for larger quantities.

Frequently Asked Questions

Which side uses 8V5955275B?

This front left headlight washer nozzle cover is catalogued for the left side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. For item AD02010-007, the approval should compare the outer surface profile with the bumper opening. The same item record should also check the nozzle outlet orientation.

Is workshop installation recommended for 8V5955275B?

Yes. A qualified workshop can access the bumper area on the A3, transfer hoses or clips safely and test the washer system for correct operation and leaks. On the listed AUDI A3 2017, technicians should verify that the cover closes without rubbing the bumper. A workshop comparison should additionally confirm that the nozzle extends and retracts freely.

Which vehicle application is listed for 8V5955275B?

8V5955275B is listed for AUDI A3 2017. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. For the left-side order line, compare product photographs with the removed part from several angles. The order review should further inspect the bumper cutout shape and surrounding contour.

Are clips, hoses or fasteners supplied with 8V5955275B?

The supply scope follows the product photographs. Reusable clips, hoses, seals, screws and separate brackets should be confirmed before the order is finalized. The product-specific check for 8V5955275B should confirm pallet requirements for larger quantities. Receiving staff should also request protective inner wrapping for painted faces.

How should 8V5955275B be packed for export?

The front left headlight washer nozzle cover should be wrapped separately, with visible faces, hose spigots, nozzle outlets and projecting tabs protected from compression and contamination. Before this headlight washer nozzle cover is accepted, state the target vehicle application. Before approval, the buyer or technician should include the full OE reference on the purchase order.

Product function: Closes the bumper washer opening and restores the visible exterior contour around the headlamp.

Fitment check: Confirm the complete OE number, model year, bumper specification and left/right position before ordering.

Supply scope: The supplied components follow the product photographs; clips, hoses, seals and fasteners are included only when shown or separately confirmed.

Surface finish: Compare the visible colour and texture with the original part; painting may be required before final installation.

Quotation information: Send the OE number, vehicle model/year, required side, quantity and delivery destination for an application-specific quotation.