8V0 945 106 Rear Bumper Light for AUDI A3 2014 Right

8V0 945 106 Rear Bumper Light Overview

This product is listed for AUDI A3 2014 at the right rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.

The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.

Before fitting the right unit, record the approved side and vehicle application for repeat-order identification to preserve access for a final electrical test where a lamp circuit is present.

Bumper Opening and Vehicle Match

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

The surrounding bumper insert, exhaust trim and lower valance can help identify the correct application version.

While the AUDI bumper opening is accessible, confirm that the cable exit, where fitted, clears the bumper reinforcement to reduce clip damage during a no-force trial installation.

During comparison of the AUDI rear component, confirm that any connector seal remains square when the housing is fully seated to prevent a visually similar version from sitting proud of the bumper.

Lens Construction and Powered Variants

Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

For a repeat order of the right version, use the opposite-side component only as an alignment reference, not as an interchange part before the packaging and carton marking are finalized.

On the 2014 A3 bumper layout, compare the outer lens edge with the moulded bumper recess before inner liners make the rear attachment points difficult to inspect.

Mounting and Final Verification

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.

At the workshop selection stage for A3, inspect the lower valance and nearby exhaust trim for adequate operating clearance so the visible gap remains even after every retaining point is engaged.

At the right rear-bumper position, check the rear housing projection against the space behind the bumper skin so the lens and housing are supported without distortion.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 8V0 945 106

Cross-reference numbers: 8V0 945 106

Internal item code: AD04004-012

Vehicle brand: AUDI

Vehicle model: A3

Model year: 2014

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Before sealing the carton, compare the packed side and quantity with the buyer’s order line.

When reviewing the 2014 vehicle, compare the bumper corner radius with the product face from more than one viewing angle so a passive reflector is not confused with an illuminated assembly.

For the AUDI A3 application, align each locating tab with the matching slot before applying hand pressure to verify that the photographed configuration matches the vehicle in the workshop.

Frequently Asked Questions

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Housing match: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.

Reflector or lamp role: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Post-fit check: After installation, confirm the lens is level with nearby trim and that no retaining tab has backed out.

Purchase information: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.