8R0 945 096B Rear Bumper Light for AUDI Q5 2010 Right

8R0 945 096B Rear Bumper Light Overview

This product is listed for AUDI Q5 2010 at the right rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

Before fitting the right unit, verify the fastener direction and the shape of the concealed support frame to prevent a visually similar version from sitting proud of the bumper.

Rear-Bumper Geometry Review

Review the corner radius, edge return and rear fastening points against the original bumper opening.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

While the AUDI bumper opening is accessible, protect the visible surface until the full perimeter gap has been accepted before the packaging and carton marking are finalized.

During comparison of the AUDI rear component, review the reflector texture and lens colour in neutral workshop light before inner liners make the rear attachment points difficult to inspect.

Lens, Housing and Harness Comparison

Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.

Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.

For a repeat order of the right version, record the approved side and vehicle application for repeat-order identification so the visible gap remains even after every retaining point is engaged.

On the 2010 Q5 bumper layout, confirm that the cable exit, where fitted, clears the bumper reinforcement so the lens and housing are supported without distortion.

Installation Completion

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

At the workshop selection stage for Q5, confirm that any connector seal remains square when the housing is fully seated so a passive reflector is not confused with an illuminated assembly.

At the right rear-bumper position, use the opposite-side component only as an alignment reference, not as an interchange part to verify that the photographed configuration matches the vehicle in the workshop.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 8R0 945 096B

Cross-reference numbers: 8R0 945 096B

Internal item code: AD04004-050

Vehicle brand: AUDI

Vehicle model: Q5

Model year: 2010

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.

Projecting tabs should be supported with shaped material instead of carrying the weight of other products.

When reviewing the 2010 vehicle, compare the outer lens edge with the moulded bumper recess to avoid contact with wiring, body edges or hot exhaust components.

For the AUDI Q5 application, inspect the lower valance and nearby exhaust trim for adequate operating clearance to keep the optical face level with the surrounding painted surface.

Frequently Asked Questions

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Shape and clips: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Rear visibility role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.

Quotation details: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.