8K0955101B Front Left Headlight Washer Nozzle for AUDI A4 2013

8K0955101B Front Left Headlight Washer Nozzle Product Overview

The component shown under 8K0955101B is a front left headlight washer nozzle intended for AUDI A4 2013. The washer nozzle receives pressurized fluid, moves toward the headlamp where applicable and directs spray across the lens surface. Confirm the left orientation, washer-system connection, bumper-side geometry against the original vehicle part.

Fitment and Washer-System Application for A4

Compatibility for 8K0955101B should be confirmed against AUDI A4 2013 and the left installation side. The review should verify that the OE reference is not for the opposite side, verify the required left or right installation side, and compare every tab, clip seat and locating shoulder. Use the removed part and product photographs to retain the removed component for a direct physical comparison, compare the complete OE marking with the removed washer component, and verify nearby parking-sensor or trim interfaces; finally, match the mounting pattern around the bumper aperture and check the washer jet position relative to the headlamp lens.

Headlight Washer Nozzle Function and Design Notes

The visible and hidden interfaces of AD02010-029 should be checked separately. For this headlight washer nozzle, review any paint-preparation requirement before fitting, check the complete supplied scope against the photographs, and inspect the molded tabs for cracks or distortion. A direct comparison with the removed part should additionally compare the visible bumper-side contour, review the hose spigot angle on the washer nozzle, and check the cap hinge or retaining point. Before the item is accepted, inspect the telescopic body for smooth movement and compare the outer surface profile with the bumper opening.

OE Identification and Side Confirmation

8K0955101B is the primary OE identity for this left front left headlight washer nozzle, while AD02010-029 is the internal item code. Match both references to the vehicle record, then review facelift and pre-facelift washer layouts. Do not substitute the mirrored side merely because the visible cover shape appears similar.

Installation and System Testing Guidance

Workshop preparation for AD02010-029 begins before the bumper area is disturbed: follow the vehicle workshop procedure for bumper removal and check that the washer unit is fully seated in its guide. During trial fitting, test for drips after the washer pump stops, retain the original fasteners unless replacements are specified, and disconnect the fluid hose without twisting the plastic spigot. Before returning the vehicle to service, confirm that the nozzle extends and retracts freely, replace distorted clips or damaged seals, and keep dirt out of open washer-fluid lines.

Receiving Inspection

When AD02010-029 arrives, receiving staff should check molded tabs for whitening, cracks or transport stress, confirm the bumper-facing edge has not been compressed in transit, and check the carton partition for evidence of part-to-part contact. Before workshop release, check the spring-return area where the component includes an actuator, verify that protective plugs remain in open fluid connections, protect the visible face again after inspection is complete, and verify the supplied scope before discarding dividers or inner bags. Complete the inspection by ensuring that staff review the production finish against the approved sample, review the hose spigot for impact damage or distortion, and retain the OE label until the washer system has passed its function test.

Product Technical Specifications

Product type: Front Left Headlight Washer Nozzle

Primary OE reference: 8K0955101B

Cross-reference numbers: 8K0 955 101B 8K0955101B

Internal item code: AD02010-029

Vehicle brand: AUDI

Vehicle model: A4

Model year: 2013

Installation position: Front bumper / headlamp washer area

Side / orientation: Left

Applicable vehicle: AUDI A4 2013

Wholesale Supply and Protective Packing

For a quotation or repeat order of 8K0955101B, please request a packing-list breakdown by internal item code, provide the complete destination address or port, and confirm sample requirements before a bulk order. Packing instructions should confirm the preferred incoterm, state any outer-carton marking requirements, and include the full OE reference on the purchase order. Before dispatch, request export-carton dimensions before freight booking and request moisture protection for sea freight.

Frequently Asked Questions

Should the washer system be tested after fitting 8K0955101B?

Yes. Check nozzle movement, cap closure, spray direction, hose routing and leakage before the bumper-area repair is completed. For item AD02010-029, the approval should inspect the bumper opening after the trial fit. The same item record should also inspect nearby wiring and sensors before refitting trim.

What should be inspected when 8K0955101B arrives?

Check the item label, side, contour, tabs, fluid connection, supplied components and carton condition before fitting or discarding the packaging. On the listed AUDI A4 2013, technicians should inspect the rear locator shape without forcing any movable section. A workshop comparison should additionally check molded tabs for whitening, cracks or transport stress.

Which side uses 8K0955101B?

This front left headlight washer nozzle is catalogued for the left side of the front bumper. Opposite-side washer parts normally use mirrored geometry and a different OE reference. For the left-side order line, check the bumper-facing surface for transport marks. The order review should further check the nozzle outlet orientation.

How should 8K0955101B be checked before installation?

Compare the OE number, side, mounting points, bumper contour, hose connection and supplied scope with the removed washer component before fitting. The product-specific check for 8K0955101B should confirm the destination-market equipment specification. Receiving staff should also compare the actuator orientation behind the bumper cover.

Which vehicle application is listed for 8K0955101B?

8K0955101B is listed for AUDI A4 2013. Confirm the complete OE reference, model year, bumper specification and installation side against the vehicle. Before this headlight washer nozzle is accepted, verify nearby parking-sensor or trim interfaces. Before approval, the buyer or technician should compare product photographs with the removed part from several angles.

Product function: Directs washer fluid toward the headlamp lens as part of the vehicle headlight-cleaning system.

Fitment check: Confirm the complete OE number, model year, bumper specification and left/right position before ordering.

Supply scope: The supplied components follow the product photographs; clips, hoses, seals and fasteners are included only when shown or separately confirmed.

System check: After installation, check hose routing, nozzle movement, spray direction and fluid leakage.

Quotation information: Send the OE number, vehicle model/year, required side, quantity and delivery destination for an application-specific quotation.