8A61-15K273-AC 1681884 Rear Bumper Light for FORD Fiesta 2009 Left

8A61-15K273-AC 1681884 Rear Bumper Light Overview

This product is listed for FORD Fiesta 2009 at the left rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.

Production date and regional bumper specification should be reviewed when several near-identical versions are available.

During comparison of the FORD rear component, protect the visible surface until the full perimeter gap has been accepted so the lens and housing are supported without distortion.

Physical Fitment Evidence

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

For a repeat order of the left version, review the reflector texture and lens colour in neutral workshop light so a passive reflector is not confused with an illuminated assembly.

On the 2009 Fiesta bumper layout, record the approved side and vehicle application for repeat-order identification to verify that the photographed configuration matches the vehicle in the workshop.

Surface, Seal and Electrical Interface

If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

At the workshop selection stage for Fiesta, confirm that the cable exit, where fitted, clears the bumper reinforcement to avoid contact with wiring, body edges or hot exhaust components.

At the left rear-bumper position, confirm that any connector seal remains square when the housing is fully seated to keep the optical face level with the surrounding painted surface.

Bumper Assembly Check

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Check the opposite side as a reference for height, angle and edge gap before completing the repair.

When reviewing the 2009 vehicle, use the opposite-side component only as an alignment reference, not as an interchange part before any modification is made to the bumper or replacement part.

For the FORD Fiesta application, compare the outer lens edge with the moulded bumper recess before deciding whether original hardware is suitable for reuse.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 8A61-15K273-AC 1681884

Cross-reference numbers: 8A61-15K273-AC 1681884

Internal item code: FD04004-039

Vehicle brand: FORD

Vehicle model: Fiesta

Model year: 2009

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Projecting tabs should be supported with shaped material instead of carrying the weight of other products.

For this Fiesta body configuration, inspect the lower valance and nearby exhaust trim for adequate operating clearance because facelift bumpers can retain the same vehicle name with different apertures.

Before approving the Fiesta part for packing, check the rear housing projection against the space behind the bumper skin so left- and right-hand stock cannot be mixed during consolidation.

Frequently Asked Questions

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Request a Product-Specific Quote

A product-specific quotation can be prepared after the vehicle, side and destination are confirmed.

Shape and clips: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.

Rear visibility role: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

Post-fit check: Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Quotation details: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.