81910-0R020 Rear Bumper Light for TOYOTA RAV4 2009-2012 Right

81910-0R020 Rear Bumper Light Overview

This product is listed for TOYOTA RAV4 2009-2012 at the right rear-bumper position. Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

For this RAV4 body configuration, compare the outer lens edge with the moulded bumper recess to reduce clip damage during a no-force trial installation.

Application and Rear-Bumper Position

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Production date and regional bumper specification should be reviewed when several near-identical versions are available.

Before approving the RAV4 part for packing, inspect the lower valance and nearby exhaust trim for adequate operating clearance to prevent a visually similar version from sitting proud of the bumper.

Before fitting the right unit, check the rear housing projection against the space behind the bumper skin before the packaging and carton marking are finalized.

Optical Face and Connector Review

Do not add wiring to a reflector-only application; use the photographs to distinguish illuminated and passive versions.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

While the TOYOTA bumper opening is accessible, compare the bumper corner radius with the product face from more than one viewing angle before inner liners make the rear attachment points difficult to inspect.

During comparison of the TOYOTA rear component, align each locating tab with the matching slot before applying hand pressure so the visible gap remains even after every retaining point is engaged.

Workshop Fitting Sequence

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

After installation, confirm the lens is level with nearby trim and that no retaining tab has backed out.

For a repeat order of the right version, check whether the original component uses a separate retainer or an integral locking tab so the lens and housing are supported without distortion.

On the 2009-2012 RAV4 bumper layout, verify the fastener direction and the shape of the concealed support frame so a passive reflector is not confused with an illuminated assembly.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 81910-0R020

Cross-reference numbers: 81910-0R020

Internal item code: TY04004-004

Vehicle brand: TOYOTA

Vehicle model: RAV4

Model year: 2009-2012

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.

At the workshop selection stage for RAV4, protect the visible surface until the full perimeter gap has been accepted to verify that the photographed configuration matches the vehicle in the workshop.

At the right rear-bumper position, review the reflector texture and lens colour in neutral workshop light to avoid contact with wiring, body edges or hot exhaust components.

Frequently Asked Questions

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

Provide the expected order quantity to receive a trade-oriented packing and supply proposal.

Bumper interface: Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Product function: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

Post-fit check: For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.

Trade-order details: For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.

Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.