81910-06070 Rear Bumper Light for TOYOTA Camry 2018 Left

81910-06070 Rear Bumper Light Overview

This product is listed for TOYOTA Camry 2018 at the left rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

At the workshop selection stage for Camry, check the rear housing projection against the space behind the bumper skin so hidden brackets are not loaded or bent during installation.

Model, Year and Side Confirmation

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

At the left rear-bumper position, compare the bumper corner radius with the product face from more than one viewing angle to preserve access for a final electrical test where a lamp circuit is present.

When reviewing the 2018 vehicle, align each locating tab with the matching slot before applying hand pressure to reduce clip damage during a no-force trial installation.

Reflector Housing and Wiring Details

Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

For the TOYOTA Camry application, check whether the original component uses a separate retainer or an integral locking tab to prevent a visually similar version from sitting proud of the bumper.

For this Camry body configuration, verify the fastener direction and the shape of the concealed support frame before the packaging and carton marking are finalized.

Installation Preparation

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Complete a visual alignment check from the rear and side, then test illumination when wiring is present.

Before approving the Camry part for packing, protect the visible surface until the full perimeter gap has been accepted before inner liners make the rear attachment points difficult to inspect.

Before fitting the left unit, review the reflector texture and lens colour in neutral workshop light so the visible gap remains even after every retaining point is engaged.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 81910-06070

Cross-reference numbers: 81910-06070

Internal item code: TY04004-011

Vehicle brand: TOYOTA

Vehicle model: Camry

Model year: 2018

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.

While the TOYOTA bumper opening is accessible, record the approved side and vehicle application for repeat-order identification so the lens and housing are supported without distortion.

During comparison of the TOYOTA rear component, confirm that the cable exit, where fitted, clears the bumper reinforcement so a passive reflector is not confused with an illuminated assembly.

Frequently Asked Questions

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Request a Product-Specific Quote

Repeat buyers can reference the vehicle application and side from their previous approved sample.

Fitment evidence: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.

Optical configuration: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Check the opposite side as a reference for height, angle and edge gap before completing the repair.

Bulk supply: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.