81490-60080 Rear Bumper Light for TOYOTA Land Cruiser 2016 Left

81490-60080 Rear Bumper Light Overview

This product is listed for TOYOTA Land Cruiser 2016 at the left rear-bumper position. This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Production date and regional bumper specification should be reviewed when several near-identical versions are available.

Before fitting the left unit, check whether the original component uses a separate retainer or an integral locking tab before any modification is made to the bumper or replacement part.

Physical Fitment Evidence

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

While the TOYOTA bumper opening is accessible, verify the fastener direction and the shape of the concealed support frame before deciding whether original hardware is suitable for reuse.

During comparison of the TOYOTA rear component, protect the visible surface until the full perimeter gap has been accepted because facelift bumpers can retain the same vehicle name with different apertures.

Surface, Seal and Electrical Interface

Confirm separately whether the removed component uses wiring, a bulb holder or an integrated LED module.

Inspect the moulded tabs from the rear and avoid placing package or hand pressure on the centre of the lens.

For a repeat order of the left version, review the reflector texture and lens colour in neutral workshop light so left- and right-hand stock cannot be mixed during consolidation.

On the 2016 Land Cruiser bumper layout, record the approved side and vehicle application for repeat-order identification so the approved product can be picked consistently in a mixed wholesale order.

Bumper Assembly Check

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.

At the workshop selection stage for Land Cruiser, confirm that the cable exit, where fitted, clears the bumper reinforcement so hidden brackets are not loaded or bent during installation.

At the left rear-bumper position, confirm that any connector seal remains square when the housing is fully seated to preserve access for a final electrical test where a lamp circuit is present.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 81490-60080

Cross-reference numbers: 81490-60080

Internal item code: TY04004-043

Vehicle brand: TOYOTA

Vehicle model: Land Cruiser

Model year: 2016

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.

Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.

When reviewing the 2016 vehicle, use the opposite-side component only as an alignment reference, not as an interchange part to reduce clip damage during a no-force trial installation.

For the TOYOTA Land Cruiser application, compare the outer lens edge with the moulded bumper recess to prevent a visually similar version from sitting proud of the bumper.

Frequently Asked Questions

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Fitment evidence: Review the corner radius, edge return and rear fastening points against the original bumper opening.

Optical configuration: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

Post-fit check: Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

Bulk supply: Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.

Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.