81456-60030 Rear Bumper Light for TOYOTA Land Cruiser 2007 Left

81456-60030 Rear Bumper Light Overview

This product is listed for TOYOTA Land Cruiser 2007 at the left rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

On the 2007 Land Cruiser bumper layout, confirm that the cable exit, where fitted, clears the bumper reinforcement to preserve access for a final electrical test where a lamp circuit is present.

Model, Year and Side Confirmation

Review the corner radius, edge return and rear fastening points against the original bumper opening.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

At the workshop selection stage for Land Cruiser, confirm that any connector seal remains square when the housing is fully seated to reduce clip damage during a no-force trial installation.

At the left rear-bumper position, use the opposite-side component only as an alignment reference, not as an interchange part to prevent a visually similar version from sitting proud of the bumper.

Reflector Housing and Wiring Details

For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.

Protect the exposed face from tools and fasteners while the bumper liner is open for access.

When reviewing the 2007 vehicle, compare the outer lens edge with the moulded bumper recess before the packaging and carton marking are finalized.

For the TOYOTA Land Cruiser application, inspect the lower valance and nearby exhaust trim for adequate operating clearance before inner liners make the rear attachment points difficult to inspect.

Installation Preparation

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

For this Land Cruiser body configuration, check the rear housing projection against the space behind the bumper skin so the visible gap remains even after every retaining point is engaged.

Before approving the Land Cruiser part for packing, compare the bumper corner radius with the product face from more than one viewing angle so the lens and housing are supported without distortion.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 81456-60030

Cross-reference numbers: 81456-60030

Internal item code: TY04004-039

Vehicle brand: TOYOTA

Vehicle model: Land Cruiser

Model year: 2007

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Projecting tabs should be supported with shaped material instead of carrying the weight of other products.

Before fitting the left unit, align each locating tab with the matching slot before applying hand pressure so a passive reflector is not confused with an illuminated assembly.

While the TOYOTA bumper opening is accessible, check whether the original component uses a separate retainer or an integral locking tab to verify that the photographed configuration matches the vehicle in the workshop.

Frequently Asked Questions

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Request a Product-Specific Quote

Destination and carton-marking requirements can be included with the vehicle-specific enquiry.

Shape and clips: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.

Rear visibility role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Complete a visual alignment check from the rear and side, then test illumination when wiring is present.

Quotation details: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Packing reference: Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.