80A 945 070 Rear Bumper Light for AUDI Q5 2018 Right

80A 945 070 Rear Bumper Light Overview

This product is listed for AUDI Q5 2018 at the right rear-bumper position. Powered variants work with the vehicle harness; non-powered variants depend on the correct reflective lens and mounting angle.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

While the AUDI bumper opening is accessible, review the reflector texture and lens colour in neutral workshop light before the packaging and carton marking are finalized.

Model, Year and Side Confirmation

Review the corner radius, edge return and rear fastening points against the original bumper opening.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

During comparison of the AUDI rear component, record the approved side and vehicle application for repeat-order identification before inner liners make the rear attachment points difficult to inspect.

For a repeat order of the right version, confirm that the cable exit, where fitted, clears the bumper reinforcement so the visible gap remains even after every retaining point is engaged.

Reflector Housing and Wiring Details

For lamp versions, the connector must lock without force and the harness should route clear of the exhaust and sharp edges.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

On the 2018 Q5 bumper layout, confirm that any connector seal remains square when the housing is fully seated so the lens and housing are supported without distortion.

At the workshop selection stage for Q5, use the opposite-side component only as an alignment reference, not as an interchange part so a passive reflector is not confused with an illuminated assembly.

Installation Preparation

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.

At the right rear-bumper position, compare the outer lens edge with the moulded bumper recess to verify that the photographed configuration matches the vehicle in the workshop.

When reviewing the 2018 vehicle, inspect the lower valance and nearby exhaust trim for adequate operating clearance to avoid contact with wiring, body edges or hot exhaust components.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 80A 945 070

Cross-reference numbers: 80A 945 070

Internal item code: AD04004-046

Vehicle brand: AUDI

Vehicle model: Q5

Model year: 2018

Installation position: Rear bumper / reflector opening

Side / orientation: Right

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

The visible face should remain separated from tape, staples and loose hardware throughout transport.

For the AUDI Q5 application, check the rear housing projection against the space behind the bumper skin to keep the optical face level with the surrounding painted surface.

For this Q5 body configuration, compare the bumper corner radius with the product face from more than one viewing angle before any modification is made to the bumper or replacement part.

Frequently Asked Questions

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Request a Product-Specific Quote

For mixed shipments, send a line-by-line quantity list so each rear-bumper position is quoted independently.

Physical comparison: Confirm that the body sits flush in the bumper aperture and that every guide tab faces the correct direction.

Lighting function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.

Wholesale enquiry: Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Packing reference: Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.