7P6 945 701B Rear Bumper Light for VOLKSWAGEN Touareg 2011 Left

7P6 945 701B Rear Bumper Light Overview

This product is listed for VOLKSWAGEN Touareg 2011 at the left rear-bumper position. Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

Before approving the Touareg part for packing, inspect the lower valance and nearby exhaust trim for adequate operating clearance before the packaging and carton marking are finalized.

Rear-Bumper Geometry Review

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Before fitting the left unit, check the rear housing projection against the space behind the bumper skin before inner liners make the rear attachment points difficult to inspect.

While the VOLKSWAGEN bumper opening is accessible, compare the bumper corner radius with the product face from more than one viewing angle so the visible gap remains even after every retaining point is engaged.

Lens, Housing and Harness Comparison

Do not add wiring to a reflector-only application; use the photographs to distinguish illuminated and passive versions.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

During comparison of the VOLKSWAGEN rear component, align each locating tab with the matching slot before applying hand pressure so the lens and housing are supported without distortion.

For a repeat order of the left version, check whether the original component uses a separate retainer or an integral locking tab so a passive reflector is not confused with an illuminated assembly.

Installation Completion

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Check the opposite side as a reference for height, angle and edge gap before completing the repair.

On the 2011 Touareg bumper layout, verify the fastener direction and the shape of the concealed support frame to verify that the photographed configuration matches the vehicle in the workshop.

At the workshop selection stage for Touareg, protect the visible surface until the full perimeter gap has been accepted to avoid contact with wiring, body edges or hot exhaust components.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 7P6 945 701B

Cross-reference numbers: 7P6 945 701B

Internal item code: VM04004-014

Vehicle brand: VOLKSWAGEN

Vehicle model: Touareg

Model year: 2011

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Before sealing the carton, compare the packed side and quantity with the buyer’s order line.

At the left rear-bumper position, review the reflector texture and lens colour in neutral workshop light to keep the optical face level with the surrounding painted surface.

When reviewing the 2011 vehicle, record the approved side and vehicle application for repeat-order identification before any modification is made to the bumper or replacement part.

Frequently Asked Questions

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How should the visible lens be packed?

Keep it isolated from carton pressure, loose hardware and neighbouring products with separate support for tabs.

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

The sales team can check whether accessories shown in the photograph are part of the requested scope.

Housing match: Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Reflector or lamp role: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

Post-fit check: Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

Purchase information: For repeat orders, quote the vehicle application and side together so the correct bumper variant is selected.