71106-TB0-H01 Front Left Fog Light Bezel for HONDA Everus G11 2011

71106-TB0-H01 Front Left Fog Light Bezel Product Overview

The product shown under 71106-TB0-H01 is a front left fog light bezel intended for HONDA Everus G11 2011. Check the left orientation, lamp opening, mounting tabs and high-specification specification against the original component.

Fitment and Application for Everus G11

For wholesale selection of 71106-TB0-H01, check the nearby lamp opening, match the locating-slot layout, and inspect the removed bezel. Before final installation, confirm the surface finish, review market-version differences, and compare the original grille section.

Before sourcing this front left fog light bezel, review the bezel orientation, compare the original grille section, and check the vehicle build date. During receiving inspection, match the outer contour, review facelift styling, and confirm the bumper position.

Before confirming this fog light bezel, inspect the lamp aperture size, match the stated trim level, and inspect the removed bezel. Before the quotation is confirmed, confirm the bumper position, check the vehicle build date, and confirm the surface finish.

Front Left Fog Light Bezel Design and Replacement Notes

For replacement in the left front area, check the lamp interface, review narrow bezel ends, and inspect the end geometry. For a repeat wholesale order, inspect the moulded face, compare mounting-hole height, and compare transferred hardware.

When separating nearby Everus G11 variants, compare vent or grille openings, inspect the moulded face, and compare the original edge profile. While reviewing the supplied photographs, review locator direction, check the bezel curvature, and compare the centre alignment.

When comparing 71106-TB0-H01 with the removed bezel, inspect the end geometry, inspect the back-side structure, and compare the original edge profile. Before final installation, review narrow bezel ends, review the outer-edge shape, and review fastening slots.

Application-Specific Identification Notes

Before a replacement is packed with 71106-TB0-H01 on the Everus G11 2011: check the nearby lamp opening. The HD02008-089 sample for the left side should check the adjoining gap. For HONDA identification, 71106-TB0-H01 also requires technicians to check lamp-to-bezel clearance. A buyer quoting HD02008-089 should state the target vehicle for the HONDA Everus G11 2011 order.

For application-specific sourcing with 71106-TB0-H01 on the Everus G11 2011: review the bezel orientation. The HD02008-089 sample for the left side should check the adjoining gap. For HONDA identification, 71106-TB0-H01 also requires technicians to confirm the fitting direction. A buyer quoting HD02008-089 should request export quotation terms for the HONDA Everus G11 2011 order.

When the bumper opening is reviewed with 71106-TB0-H01 on the Everus G11 2011: review the bezel orientation. The HD02008-089 sample for the left side should inspect the end geometry. For HONDA identification, 71106-TB0-H01 also requires technicians to confirm an evenly seated fit. A buyer quoting HD02008-089 should check the ordered mounting side for the HONDA Everus G11 2011 order.

A trim-level comparison requires with 71106-TB0-H01 on the Everus G11 2011: check the nearby lamp opening. The HD02008-089 sample for the left side should check the lamp interface. For HONDA identification, 71106-TB0-H01 also requires technicians to support the bumper cover evenly. A buyer quoting HD02008-089 should request supported carton packing for the HONDA Everus G11 2011 order.

Installation Guidance

For wholesale selection of 71106-TB0-H01, trial-fit the bezel without force, protect nearby painted surfaces, and support the bumper cover evenly. When checking the bumper opening, clean the bumper mounting area, verify the lamp remains centred, and confirm the finished bumper gap.

Before sourcing this front left fog light bezel, avoid bending moulded tabs, check the final perimeter, and support the bumper cover evenly. At the workshop preparation stage, confirm every locator engages, review separate hardware needs, and clean the bumper mounting area.

Before confirming this fog light bezel, review separate hardware needs, retain the removed bezel for comparison, and inspect damaged mounting points. For a repeat wholesale order, clean the bumper mounting area, confirm an evenly seated fit, and inspect each screw point.

Product Technical Specifications

Product type: Front Left Fog Light Bezel

Primary OE reference: 71106-TB0-H01

Cross-reference numbers: 71106-TB0-H01 71106TB0H01

Internal item code: HD02008-089

Vehicle brand: HONDA

Vehicle model: Everus G11

Model year: 2011

Installation position: Front

Side / orientation: Left

Version / finish: high-specification

Applicable vehicle: HONDA Everus G11 2011

Wholesale Supply and Packing

For replacement in the left front area, confirm separate clip requirements, state annual purchasing volume, and state the destination port. Before clips or hardware are transferred, state the required quantity, include the complete OE reference, and protect projecting locator tabs.

When separating nearby Everus G11 variants, state the destination port, confirm sample requirements, and provide the delivery country. During the physical comparison, compare the supplied photographs, request supported carton packing, and confirm the packing method.

When comparing 71106-TB0-H01 with the removed bezel, include the complete OE reference, send photographs of the removed part, and provide the delivery country. When checking the bumper opening, state the required quantity, request protective inner wrapping, and confirm the delivery schedule.

Frequently Asked Questions

Does 71106-TB0-H01 include the complete lamp assembly?

No. This listing covers the pictured front left fog light bezel. The fog lamp, bulbs, wiring, switches and separate clips are not included unless they are visibly shown. For Everus G11, compare the full OE marking, inspect the moulded face, clean the bumper mounting area, and state the required quantity before installation or quotation.

How should 71106-TB0-H01 be protected for export?

The bezel should be supported inside the carton with its narrow edges, lamp opening and projecting tabs protected against compression, abrasion and impact. For Everus G11, review the bezel orientation, check the adjoining gap, check lamp-to-bezel clearance, and state the target vehicle before installation or quotation.

What vehicle application is listed for 71106-TB0-H01?

71106-TB0-H01 is presented for HONDA Everus G11 2011. Confirm the full OE reference, model year, trim version and installation side against the removed part before ordering. For Everus G11, compare every fixing tab, inspect the moulded face, clean the bumper mounting area, and state the required quantity before installation or quotation.

Can photographs alone confirm 71106-TB0-H01 fitment?

Photographs help with shape and finish comparison, but the OE number, vehicle year, side, trim specification and mounting geometry should also agree. For Everus G11, inspect the lamp aperture size, check the adjoining gap, check lamp-to-bezel clearance, and state the target vehicle before installation or quotation.

Does trim specification matter for 71106-TB0-H01?

Yes. high-specification can change the opening pattern, finish and locator positions, so compare the removed bezel and bumper before purchase. For Everus G11, compare the original grille section, inspect the moulded face, clean the bumper mounting area, and state the required quantity before installation or quotation.

Request a Quote

Send the complete OE reference 71106-TB0-H01 , vehicle details, mounting side, quantity and destination. AutoParts can review the application before preparing a product-specific export quotation.

Fitment note: 71106-TB0-H01: check the nearby lamp opening; HD02008-089: review the bezel orientation; Everus G11 2011: inspect the lamp aperture size

Product comparison: 71106-TB0-H01: inspect the moulded face; HD02008-089: inspect the moulded face; Left: inspect the moulded face

Installation note: HD02008-089: check lamp-to-bezel clearance; 71106-TB0-H01: clean the bumper mounting area; Everus G11: check lamp-to-bezel clearance

Wholesale enquiry: 71106-TB0-H01: state the required quantity; HD02008-089: state the target vehicle; HONDA Everus G11 2011: state the target vehicle