4M0 945 095 Rear Bumper Light for AUDI Q7 2016 Left

4M0 945 095 Rear Bumper Light Overview

This product is listed for AUDI Q7 2016 at the left rear-bumper position. Some versions are passive reflectors, while others contain a lamp or wiring. The photographed configuration defines the supplied type.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

When reviewing the 2016 vehicle, inspect the lower valance and nearby exhaust trim for adequate operating clearance because facelift bumpers can retain the same vehicle name with different apertures.

Vehicle Fitment and Bumper Interface

Use the product photograph to compare the exposed face and the concealed bracket layout as one assembly.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

For the AUDI Q7 application, check the rear housing projection against the space behind the bumper skin so left- and right-hand stock cannot be mixed during consolidation.

For this Q7 body configuration, compare the bumper corner radius with the product face from more than one viewing angle so the approved product can be picked consistently in a mixed wholesale order.

Reflector, Lens and Electrical Configuration

Where a cable is fitted, inspect the seal and connector keying so the replacement does not introduce moisture or terminal stress.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

Before approving the Q7 part for packing, align each locating tab with the matching slot before applying hand pressure so hidden brackets are not loaded or bent during installation.

Before fitting the left unit, check whether the original component uses a separate retainer or an integral locking tab to preserve access for a final electrical test where a lamp circuit is present.

Installation and Functional Check

Check the mounting direction and side before installation; left and right components are not automatically interchangeable.

Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.

While the AUDI bumper opening is accessible, verify the fastener direction and the shape of the concealed support frame to reduce clip damage during a no-force trial installation.

During comparison of the AUDI rear component, protect the visible surface until the full perimeter gap has been accepted to prevent a visually similar version from sitting proud of the bumper.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 4M0 945 095

Cross-reference numbers: 4M0 945 095

Internal item code: AD04004-051

Vehicle brand: AUDI

Vehicle model: Q7

Model year: 2016

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.

For a repeat order of the left version, review the reflector texture and lens colour in neutral workshop light before the packaging and carton marking are finalized.

On the 2016 Q7 bumper layout, record the approved side and vehicle application for repeat-order identification before inner liners make the rear attachment points difficult to inspect.

Frequently Asked Questions

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Request a Product-Specific Quote

Clear application details allow the sales team to separate reflector and illuminated versions in the offer.

Fitment evidence: Compare the visible outline, rear housing depth and locating tabs with the removed part before ordering.

Optical configuration: Function and fit are linked: the correct optical face must also align with the bumper surface and surrounding trim.

Selection context: Production date and regional bumper specification should be reviewed when several near-identical versions are available.

Post-fit check: Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

Bulk supply: For a wholesale quotation, provide vehicle details, required side, quantity, destination and a photograph of the removed part.

Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.