4F0 941 700 Fog Light for AUDI A6 2005 Right

4F0 941 700 Fog Light Product Overview

For OE-led sourcing, this page connects the lamp assembly with the stated model, year and mounting side. 4F0 941 700 is catalogued as a fog light for AUDI A6 2005, installed at the right front bumper position.

4F0 941 700 — Vehicle Lighting Role

A front fog lamp adds low-mounted illumination in poor visibility while keeping the beam close to the road surface. For 4F0 941 700 on the listed A6, evaluate the optical role together with the bumper aperture, nearby trim and vehicle circuit recorded under SKU AD04002-026.

For SKU AD04002-026, identify any market-specific lighting equipment. Quoting 4F0 941 700 with the AUDI A6 2005 and right position helps separate lighting-technology and model-year variants during packing.

AD04002-026 — Part Number and Geometry Review

Start with the full reference 4F0 941 700; then verify that the listed side matches the vehicle. Item AD04002-026 should not be approved if its housing, bracket layout, right orientation or market specification differs from the removed fog light.

4F0 941 700 — Optical and Connector Details

Use the 4F0 941 700 page photographs to compare the heat shield, bulb seat and rear cap layout. For electrical compatibility on SKU AD04002-026, compare plug locking tabs and wiring direction and confirm the plug reaches its locked position without modification.

AD04002-026 — Workshop Preparation

Before securing 4F0 941 700, inspect damaged brackets before installing the replacement. After connecting SKU AD04002-026, test its stated lighting function and check alignment, clearance and harness routing around the front bumper area.

Automotive Lighting Product Specifications

Product type: Fog Light

Primary OE reference: 4F0 941 700

Cross-reference numbers: 4F0 941 700

Internal item code: AD04002-026

Vehicle brand: AUDI

Vehicle model: A6

Model year: 2005

Installation position: Front bumper

Installation side: Right

Lighting version: Match the photographed configuration

Product function: Vehicle exterior lighting for the stated bumper position

Wholesale Supply and Protective Packing

For 4F0 941 700, the lens face is isolated from carton pressure, while projecting brackets are supported against impact. For SKU AD04002-026, carton selection accounts for housing depth, mounting ears and any exposed aiming hardware.

Frequently Asked Questions

How is the 4F0 941 700 optical surface protected for shipping?

Packing for SKU AD04002-026 should isolate the lens from pressure and support projecting tabs, connector areas and adjustment hardware inside the carton.

Why compare the bumper opening for 4F0 941 700?

SKU AD04002-026 may resemble another lamp while differing in bracket spacing, housing depth or bezel interface; those differences can prevent correct seating.

How should 4F0 941 700 be installed?

For item AD04002-026, use a no-force trial fit, transfer only suitable original hardware, secure the housing evenly and test function before reinstalling liners or trim.

What information is useful for a wholesale quotation?

Provide 4F0 941 700, SKU AD04002-026, the vehicle application, mounting side, quantity, destination and photographs of the original lamp.

Can model year alone confirm 4F0 941 700 fitment?

No. For SKU AD04002-026, vehicles built in the same year can use different lighting packages, so use 4F0 941 700 and the removed lamp geometry as the primary evidence.

Request a Product-Specific Quote

Send the complete OE reference 4F0 941 700, internal number AD04002-026, vehicle details, side, quantity and destination. AutoParts can review the photographed configuration before preparing a trade quotation.

Fitment basis: Match the OE number, vehicle application, model year and installation side with the original lamp.

Housing and lens check: Match the lamp contour, body depth and adjuster arrangement before confirming the replacement.

Mounting comparison: Check the mounting tabs and hole positions for a direct fit without forcing the brackets.

Electrical connection: Confirm the connector shape, terminal count and locking tab match the vehicle harness.

Installation guidance: Inspect nearby brackets for damage, then verify clearance after the lamp is secured.

Quotation information: Quote the OE reference together with the vehicle, side and quantity to identify the correct version.