34550-TLY-H01 Rear Bumper Light for HONDA CR-V 2017 Left

34550-TLY-H01 Rear Bumper Light Overview

This product is listed for HONDA CR-V 2017 at the left rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

Before fitting the left unit, confirm that any connector seal remains square when the housing is fully seated so a passive reflector is not confused with an illuminated assembly.

Model, Year and Side Confirmation

Review the corner radius, edge return and rear fastening points against the original bumper opening.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

While the HONDA bumper opening is accessible, use the opposite-side component only as an alignment reference, not as an interchange part to verify that the photographed configuration matches the vehicle in the workshop.

During comparison of the HONDA rear component, compare the outer lens edge with the moulded bumper recess to avoid contact with wiring, body edges or hot exhaust components.

Reflector Housing and Wiring Details

Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

For a repeat order of the left version, inspect the lower valance and nearby exhaust trim for adequate operating clearance to keep the optical face level with the surrounding painted surface.

On the 2017 CR-V bumper layout, check the rear housing projection against the space behind the bumper skin before any modification is made to the bumper or replacement part.

Installation Preparation

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

For reflector types, confirm correct orientation; for powered types, test the circuit before closing access panels.

At the workshop selection stage for CR-V, compare the bumper corner radius with the product face from more than one viewing angle before deciding whether original hardware is suitable for reuse.

At the left rear-bumper position, align each locating tab with the matching slot before applying hand pressure because facelift bumpers can retain the same vehicle name with different apertures.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 34550-TLY-H01

Cross-reference numbers: 34550-TLY-H01

Internal item code: HD04004-077

Vehicle brand: HONDA

Vehicle model: CR-V

Model year: 2017

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.

Before sealing the carton, compare the packed side and quantity with the buyer’s order line.

When reviewing the 2017 vehicle, check whether the original component uses a separate retainer or an integral locking tab so left- and right-hand stock cannot be mixed during consolidation.

For the HONDA CR-V application, verify the fastener direction and the shape of the concealed support frame so the approved product can be picked consistently in a mixed wholesale order.

Frequently Asked Questions

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Housing match: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Reflector or lamp role: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Verify that bumper movement does not load the lens and that the component remains fully clipped at every corner.

Purchase information: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.