34350-TET-H01 Rear Bumper Light for HONDA Civic 2016 Left

34350-TET-H01 Rear Bumper Light Overview

This product is listed for HONDA Civic 2016 at the left rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.

Production date and regional bumper specification should be reviewed when several near-identical versions are available.

For the HONDA Civic application, confirm that any connector seal remains square when the housing is fully seated to preserve access for a final electrical test where a lamp circuit is present.

Physical Fitment Evidence

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

For this Civic body configuration, use the opposite-side component only as an alignment reference, not as an interchange part to reduce clip damage during a no-force trial installation.

Before approving the Civic part for packing, compare the outer lens edge with the moulded bumper recess to prevent a visually similar version from sitting proud of the bumper.

Surface, Seal and Electrical Interface

If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.

Do not polish or modify the lens before fitment confirmation; altered parts are harder to compare accurately.

Before fitting the left unit, inspect the lower valance and nearby exhaust trim for adequate operating clearance before the packaging and carton marking are finalized.

While the HONDA bumper opening is accessible, check the rear housing projection against the space behind the bumper skin before inner liners make the rear attachment points difficult to inspect.

Bumper Assembly Check

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

During comparison of the HONDA rear component, compare the bumper corner radius with the product face from more than one viewing angle so the visible gap remains even after every retaining point is engaged.

For a repeat order of the left version, align each locating tab with the matching slot before applying hand pressure so the lens and housing are supported without distortion.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 34350-TET-H01

Cross-reference numbers: 34350-TET-H01

Internal item code: HD04004-030

Vehicle brand: HONDA

Vehicle model: Civic

Model year: 2016

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.

On the 2016 Civic bumper layout, check whether the original component uses a separate retainer or an integral locking tab so a passive reflector is not confused with an illuminated assembly.

At the workshop selection stage for Civic, verify the fastener direction and the shape of the concealed support frame to verify that the photographed configuration matches the vehicle in the workshop.

Frequently Asked Questions

What if the bumper opening differs?

Stop the installation and compare market version, trim level and hidden mounting geometry before modifying any part.

Should original clips be reused?

Reuse hardware only when it is undamaged and correct for the photographed housing; replace distorted retainers.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

How is a passive reflector checked?

Confirm the lens orientation, reflective face and flush fit without adding wiring that was not present originally.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Request a Product-Specific Quote

AutoParts can review the pictured configuration before preparing a quantity-based offer.

Fitment evidence: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.

Optical configuration: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

Post-fit check: Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

Bulk supply: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.