26565-5C000 Rear Bumper Light for NISSAN Livina Left

26565-5C000 Rear Bumper Light Overview

This product is listed for NISSAN Livina at the left rear-bumper position. Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Use the removed component as the physical reference for outer shape, housing projection and clip location.

For a repeat order of the left version, review the reflector texture and lens colour in neutral workshop light so hidden brackets are not loaded or bent during installation.

Rear-Bumper Geometry Review

Review the corner radius, edge return and rear fastening points against the original bumper opening.

Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

On the specified production period Livina bumper layout, record the approved side and vehicle application for repeat-order identification to preserve access for a final electrical test where a lamp circuit is present.

At the workshop selection stage for Livina, confirm that the cable exit, where fitted, clears the bumper reinforcement to reduce clip damage during a no-force trial installation.

Lens, Housing and Harness Comparison

Powered assemblies should be tested for the intended rear-lighting function before the bumper liner is reinstalled.

Check the lens for scratches, cracks and distortion, then compare its moulded edge with the original component.

At the left rear-bumper position, confirm that any connector seal remains square when the housing is fully seated to prevent a visually similar version from sitting proud of the bumper.

When reviewing the specified production period vehicle, use the opposite-side component only as an alignment reference, not as an interchange part before the packaging and carton marking are finalized.

Installation Completion

Clean the bumper opening, inspect reusable clips and verify an even edge gap before final fastening.

Once seated, inspect the perimeter gap and verify that the bumper surface remains relaxed rather than distorted.

For the NISSAN Livina application, compare the outer lens edge with the moulded bumper recess before inner liners make the rear attachment points difficult to inspect.

For this Livina body configuration, inspect the lower valance and nearby exhaust trim for adequate operating clearance so the visible gap remains even after every retaining point is engaged.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 26565-5C000

Cross-reference numbers: 26565-5C000

Internal item code: NS04004-001

Vehicle brand: NISSAN

Vehicle model: Livina

Model year: Not specified

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Send front and rear photographs when the bumper uses several visually similar lens or wiring configurations.

Side-specific labels reduce picking mistakes during consolidation of mixed bumper-light orders.

Before approving the Livina part for packing, check the rear housing projection against the space behind the bumper skin so the lens and housing are supported without distortion.

Before fitting the left unit, compare the bumper corner radius with the product face from more than one viewing angle so a passive reflector is not confused with an illuminated assembly.

Frequently Asked Questions

Which physical points matter most?

Compare exposed shape, housing depth, locating tabs, fastener spacing and any electrical connector.

Can the opposite side use the same part?

Do not assume interchangeability; lens angle, contour, clips and bumper recess are normally side-specific.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

When should photographs be supplied?

Send front, rear and bumper-opening images when the original marking is unclear or several versions share the vehicle name.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

Request a Product-Specific Quote

Where the application is uncertain, send bumper-opening and rear-housing photographs for comparison first.

Bumper interface: Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

Product function: This component completes the rear bumper lighting area and must match the correct side, lens type and vehicle trim.

Selection context: Check whether the bumper carries a plain reflector or an illuminated unit before approving the replacement.

Post-fit check: Photograph the completed fit for repeat-order records when the vehicle uses an uncommon market specification.

Trade-order details: Mixed orders should list left and right quantities separately and identify reflector-only and illuminated versions.

Packing reference: Projecting tabs should be supported with shaped material instead of carrying the weight of other products.