1K8 945 105 Rear Bumper Light for VOLKSWAGEN Scirocco 2009 Left

1K8 945 105 Rear Bumper Light Overview

This product is listed for VOLKSWAGEN Scirocco 2009 at the left rear-bumper position. The part occupies a vehicle-specific bumper opening and may function as a reflector, rear fog lamp or auxiliary marker.

Compare both the visible surface and the rear attachment geometry to avoid selecting a cosmetic look-alike.

Before fitting the left unit, compare the bumper corner radius with the product face from more than one viewing angle before inner liners make the rear attachment points difficult to inspect.

Model, Year and Side Confirmation

Check the bumper recess, outer contour and clip orientation; similar reflectors can use different hidden mounts.

A correct vehicle name is only the starting point; market trim and facelift details can change the reflector opening.

While the VOLKSWAGEN bumper opening is accessible, align each locating tab with the matching slot before applying hand pressure so the visible gap remains even after every retaining point is engaged.

During comparison of the VOLKSWAGEN rear component, check whether the original component uses a separate retainer or an integral locking tab so the lens and housing are supported without distortion.

Reflector Housing and Wiring Details

If the original unit is powered, compare the socket, terminal count, cable exit and locking tab before installation.

Protect the exposed face from tools and fasteners while the bumper liner is open for access.

For a repeat order of the left version, verify the fastener direction and the shape of the concealed support frame so a passive reflector is not confused with an illuminated assembly.

On the 2009 Scirocco bumper layout, protect the visible surface until the full perimeter gap has been accepted to verify that the photographed configuration matches the vehicle in the workshop.

Installation Preparation

After fitting, inspect flushness from several angles and test the lamp where an electrical function is present.

Make sure the component does not touch hot exhaust trim or trap wiring against a sharp body edge.

At the workshop selection stage for Scirocco, review the reflector texture and lens colour in neutral workshop light to avoid contact with wiring, body edges or hot exhaust components.

At the left rear-bumper position, record the approved side and vehicle application for repeat-order identification to keep the optical face level with the surrounding painted surface.

Automotive Lighting Product Specifications

Product type: Rear Bumper Light

Primary OE reference: 1K8 945 105

Cross-reference numbers: 1K8 945 105

Internal item code: VM04004-005

Vehicle brand: VOLKSWAGEN

Vehicle model: Scirocco

Model year: 2009

Installation position: Rear bumper / reflector opening

Side / orientation: Left

Configuration: Match the photographed reflector or powered-lamp version

Wholesale Supply and Protective Packing

Confirm the required quantity and packaging method; exposed lens faces and projecting tabs need separate protection.

Powered versions benefit from a clean connector cover, while reflector versions need firm support around the rear frame.

When reviewing the 2009 vehicle, confirm that the cable exit, where fitted, clears the bumper reinforcement before any modification is made to the bumper or replacement part.

For the VOLKSWAGEN Scirocco application, confirm that any connector seal remains square when the housing is fully seated before deciding whether original hardware is suitable for reuse.

Frequently Asked Questions

Why can the same model year use another version?

Regional equipment, facelift changes and bumper trim packages can alter the opening or electrical configuration.

Can appearance alone confirm compatibility?

No. A similar colour and outline can hide different clips, housing depth, wiring or side orientation.

What should be tested after fitting?

Check panel alignment and, for powered versions, verify the intended rear-lighting function before closing access panels.

Is this component illuminated or reflector-only?

Use the product photographs to confirm whether the rear body carries a connector, bulb holder or LED wiring.

What details help with a wholesale quote?

Provide vehicle, year, side, quantity, destination and clear photographs of the removed component.

Request a Product-Specific Quote

Sharing the removed-part photograph reduces revision time when several bumper styles exist for one model year.

Fitment evidence: Match the lens perimeter and rear support geometry rather than relying on colour or overall appearance alone.

Optical configuration: Rear-bumper lighting improves low-mounted vehicle visibility; reflector-only versions return light without an electrical connection.

Selection context: Bumper designs can change during a model cycle, so verify the lens face and hidden support points together.

Post-fit check: Reinstall the liner only after the housing is secure and the cable, if fitted, has adequate clearance.

Bulk supply: Trade enquiries should include the vehicle year, model, bumper position and destination market for accurate picking.

Packing reference: The visible face should remain separated from tape, staples and loose hardware throughout transport.